Agp Pro Slot

Accelerated Graphics Port File:Accelerated Graphics Port (logo).svg
Universal AGP slot (orange, top) and PCI 2.2 slot (blue, bottom)
Year created1996; 24 years ago
Created byIntel
Superseded byPCI Express (2004)
Width in bits32
Number of devicesOne device per slot
SpeedUp to 2133 MB/s

The Accelerated Graphics Port (often shortened to AGP) is a high-speed point-to-point channel for attaching a video card to a computer system, primarily to assist in the acceleration of 3D computer graphics. It was originally designed as a successor to PCI-type connections for video cards. Since 2004, AGP has been progressively phased out in favor of PCI Express (PCIe); by mid-2008, PCI Express cards dominated the market and only a few AGP models were available.[1]

  • It allows the AGP board to be tested in a AGP-PRO slot. The adapter avoids misalignment of the gold fingers between the two standards. The extender connector on top, features a AGP connector. User need to specify 1.5VDD or 3.3VDD connector on the AGP side. The default is 3.3VDD. The gold finger features universal AGP-PRO cut.
  • ATI 16MB AGP RAGE PRO VIDEO CARD WITH VGA OUTPUT. $115.00 +$12.57 shipping. Compatible Slot. PCI Express 2.0 x16.
  • I think the AGP pro slot is there to support some super high end commercial boards which I think run different voltage/current loads. An AGP pro seems to be backwards compatible as I have seen many.

The Radeon 9800 Pro is an AGP 8x card compatible with AGP 2x and 4x slots. It was a build-to-order for the 2003 Power Mac G5, 2004 Power Mac G5, and 2005 Power Mac G5. Apple's version of the card included 256 MB of RAM.

  • 3Versions
    • 3.1Official extensions
    • 3.2Unofficial variations

Advantages over PCI

As computers increasingly became graphically oriented, successive generations of graphics adapters began to push the limits of PCI, a bus with shared bandwidth. This led to the development of AGP, a 'bus' dedicated to graphics adapters.

The primary advantage of AGP over PCI is that it provides a dedicated pathway between the slot and the processor rather than sharing the PCI bus. In addition to a lack of contention for the bus, the direct connection allows for higher clock speeds. AGP also uses sideband addressing, meaning that the address and data buses are separated so the entire packet does not need to be read to get addressing information. This is done by adding an extra 8-bit 'SideBand Address' bus that allows the graphics controller to issue new AGP requests and commands at the same time other AGP data is flowing through the main 32 address/data (AD) lines. This results in improved overall AGP data throughput.

In addition, to load a texture, a PCI graphics card must copy it from the system's RAM into the card's video memory, whereas an AGP card is capable of reading textures directly from system RAM using the graphics address remapping table (GART), which reapportions main memory as needed for texture storage, allowing the graphics card to access them directly.[2] The maximum amount of system memory available to AGP is defined as the AGP aperture.


An AGP card

The AGP slot first appeared on x86-compatible system boards based on Socket 7 Intel P5Pentium and Slot 1P6Pentium II processors. Intel introduced AGP support with the i440LX Slot 1 chipset on August 26, 1997, and a flood of products followed from all the major system board vendors.[3]

The first Socket 7 chipsets to support AGP were the VIAApollo VP3, SiS 5591/5592, and the ALI Aladdin V. Intel never released an AGP-equipped Socket 7 chipset. FIC demonstrated the first Socket 7 AGP system board in November 1997 as the FIC PA-2012 based on the VIA Apollo VP3 chipset, followed very quickly by the EPoX P55-VP3 also based on the VIA VP3 chipset which was first to market.[4]

Early video chipsets featuring AGP support included the Rendition Vérité V2200, 3dfxVoodoo Banshee, NvidiaRIVA 128, 3Dlabs PERMEDIA 2, Intel i740, ATI Rage series, Matrox Millennium II, and S3 ViRGE GX/2. Some early AGP boards used graphics processors built around PCI and were simply bridged to AGP. This resulted in the cards benefiting little from the new bus, with the only improvement used being the 66 MHz bus clock, with its resulting doubled bandwidth over PCI, and bus exclusivity. Examples of such cards were the Voodoo Banshee, Vérité V2200, Millennium II, and S3 ViRGE GX/2. Intel's i740 was explicitly designed to exploit the new AGP feature set. In fact it was designed to texture only from AGP memory, making PCI versions of the board difficult to implement (local board RAM had to emulate AGP memory.)

Agp Pro Slot Gun


Microsoft first introduced AGP support into Windows 95 OEM Service Release 2 (OSR2 version 1111 or 950B) via the USB SUPPLEMENT to OSR2 patch.[5] After applying the patch the Windows 95 system became Windows 95 version 4.00.950 B. The first Windows NT-based operating system to receive AGP support was Windows NT 4.0 with Service Pack 3, introduced in 1997. Linux support for AGP enhanced fast data transfers was first added in 1999 with the implementation of the AGPgart kernel module.


AGP and PCI: 32-bit buses operating at 66 and 33 MHz respectively
SpecificationVoltageClockSpeedTransfers/clockRate (MB/s)
PCI3.3/5 V33 MHz1133
PCI 2.13.3/5 V33/66 MHz1266
AGP 1.03.3 V66 MHz1266
AGP 1.03.3 V66 MHz2533
AGP 2.01.5 V66 MHz41066
AGP 3.00.8 V66 MHz82133
AGP 3.5*0.8 V66 MHz82133

Intel released 'AGP specification 1.0' in 1997.[6] It specified 3.3 V signals and 1× and 2× speeds.[3] Specification 2.0 documented 1.5 V signaling, which could be used at 1×, 2× and the additional 4× speed[7][8] and 3.0 added 0.8 V signaling, which could be operated at 4× and 8× speeds.[9] (1× and 2× speeds are physically possible, but were not specified.)

Available versions are listed in the table on the right.

AGP version 3.5 is only publicly mentioned by Microsoft under Universal Accelerated Graphics Port (UAGP), which specifies mandatory supports of extra registers once marked optional under AGP 3.0. Upgraded registers include PCISTS, CAPPTR, NCAPID, AGPSTAT, AGPCMD, NISTAT, NICMD. New required registers include APBASELO, APBASEHI, AGPCTRL, APSIZE, NEPG, GARTLO, GARTHI.

There are various physical interfaces (connectors); see the Compatibility section.

Official extensions

AGP graphics card (AppleMacintosh)
AGP Pro graphics card


An official extension for cards that required more electrical power, with a longer slot with additional pins for that purpose. AGP Pro cards were usually workstation-class cards used to accelerate professional computer-aided design applications employed in the fields of architecture, machining, engineering, simulations, and similar fields.[10]

Agp pro slot machine

64-bit AGP

A 64-bit channel was once proposed as an optional standard for AGP 3.0 in draft documents,[11] but it was dropped in the final version of the standard.

The standard allows 64-bit transfer for AGP8× reads, writes, and fast writes; 32-bit transfer for PCI operations.

Unofficial variations

A number of non-standard variations of the AGP interface have been produced by manufacturers.

Internal AGP interface

Ultra-AGP, Ultra-AGPII
It is an internal AGP interface standard used by SiS for the north bridge controllers with integrated graphics. The original version supports same bandwidth as AGP 8×, while Ultra-AGPII has maximum 3.2GB/s bandwidth.

Agp Pro Slot

PCI-based AGP ports

AGP Express
Not a true AGP interface, but allows an AGP card to be connected over the legacy PCI bus on a PCI Express motherboard. It is a technology used on motherboards made by ECS, intended to allow an existing AGP card to be used in a new motherboard instead of requiring a PCIe card to be obtained (since the introduction of PCIe graphics cards few motherboards provide AGP slots). An 'AGP Express' slot is basically a PCI slot (with twice the electrical power) with an AGP connector. It offers backward compatibility with AGP cards, but provides incomplete support[12] (some AGP cards do not work with AGP Express) and reduced performance—the card is forced to use the shared PCI bus at its lower bandwidth, rather than having exclusive use of the faster AGP.
The ASRock Graphics Interface (AGI) is a proprietary variant of the Accelerated Graphics Port (AGP) standard. Its purpose is to provide AGP-support for ASRock motherboards that use chipsets lacking native AGP support. However, it is not fully compatible with AGP, and several video card chipsets are known not to be supported.
The EpoX Advanced Graphics eXtended (AGX) is another proprietary AGP variant with the same advantages and disadvantages as AGI. User manuals recommend not using AGP 8× ATI cards with AGX slots.
The Biostar Xtreme Graphics Port is another AGP variant, also with the same advantages and disadvantages as AGI and AGX.

PCIe based AGP ports

The Advanced Graphics Riser is a variation of the AGP port used in some PCIe motherboards made by MSI to offer limited backwards compatibility with AGP. It is, effectively, a modified PCIe slot allowing for performance comparable to an AGP 4×/8× slot,[13] but does not support all AGP cards; the manufacturer published a list of some cards and chipsets that work with the modified slot.[14]


Compatibility, AGP Keys on card (top), on slot (bottom)

AGP cards are backward and forward compatible within limits. 1.5 V-only keyed cards will not go into 3.3 V slots and vice versa, though 'Universal' cards exist which will fit into either type of slot. There are also unkeyed 'Universal' slots that will accept either type of card. When an AGP Universal card is plugged-into an AGP Universal slot, only the 1.5 V portion of the card is used. Some cards, like Nvidia's GeForce 6 series (except the 6200) or ATI's Radeon X800 series, only have keys for 1.5 V to prevent them from being installed in older mainboards without 1.5 V support. Some of the last modern cards with 3.3 V support were the Nvidia GeForce FX series (FX 5200, FX 5500, FX 5700, some FX 5800, FX 5900 and some FX 5950), Geforce 6 Series (6200, 6600/6600 LE/6600 GT only) and the ATI Radeon 9500/9700/9800(R350) (but not 9600/9800(R360)). Some Geforce 6200 and Geforce 6600 cards will function with AGP 1.0 (3.3v) slots.

AGP Pro cards will not fit into standard slots, but standard AGP cards will work in a Pro slot. Motherboards equipped with a Universal AGP Pro slot will accept a 1.5 V or 3.3 V card in either the AGP Pro or standard AGP configuration, a Universal AGP card, or a Universal AGP Pro card.


Some cards incorrectly have dual notches, and some motherboards incorrectly have fully open slots, allowing a card to be plugged into a slot that does not support the correct signaling voltage, which may damage card or motherboard. Some incorrectly designed older 3.3 V cards have the 1.5 V key.

There are some proprietary systems incompatible with standard AGP; for example, ApplePower Macintosh computers with the Apple Display Connector (ADC) have an extra connector which delivers power to the attached display. Some cards designed to work with a specific CPU architecture (e.g., PC, Apple) may not work with others due to firmware issues.

Mark Allen of made the following comments regarding Practical AGP Compatibility for AGP 3.0 and AGP 2.0:[15]

'...nobody makes AGP 3.0 cards, and nobody makes AGP 3.0 motherboards. At least not any manufacturers I can find. Every single video card I could find which claimed to be an AGP 3.0 card was actually a universal 1.5V AGP 3.0 card. And every motherboard which claimed to be an AGP 3.0 motherboard turned out to be a universal 1.5V AGP 3.0 motherboard. It makes sense, if you think about it, because if anyone actually shipped a consumer-oriented product which supported only 0.8 volts, they would end up with lots of confused customers and a support nightmare. In the consumer market, you'd have to be crazy to ship a 0.8 volt only product.'

Power consumption

AGP power provisioning
Slot Type3.3 V5 V12 V3.3 V Aux1.5 V3.3 V[lower-alpha 1]12 V[lower-alpha 1]Total power
AGP6 A2 A1 A0.375 mA2 A--48.25 W[lower-alpha 2]
AGP Pro1107.6 A9.2 A50 to 110 W
AGP Pro507.6 A4.17 A25 to 50 W

Actual power supplied by an AGP slot depends upon the card used. The maximum current drawn from the various rails is given in the specifications for the various versions. For example, if maximum current is drawn from all supplies and all voltages are at their specified upper limits,[9]:95 an AGP 3.0 slot can supply up to 48.25 watts; this figure can be used to specify a power supply conservatively, but in practice a card is unlikely ever to draw more than 40 W from the slot, with many using less. AGP Pro provides additional power up to 110 W. Many AGP cards had additional power connectors to supply them with more power than the slot could provide.

Legacy use

By 2010 few new motherboards had AGP slots. No new motherboard chipsets were equipped with AGP support, but motherboards continued to be produced with older chipsets with support for AGP.

Graphics processors of this period use PCI-Express, a general-purpose (not restricted to graphics) standard that supports higher data transfer rates and full-duplex. To create AGP-compatible graphics cards, those chips require an additional PCIe-to-AGP bridge-chip to convert PCIe signals to and from AGP signals. This incurs additional board costs due to the need for the additional bridge chip and for a separate AGP-designed circuit board.

Various manufacturers of graphics cards continued to produce AGP cards for the shrinking AGP user-base. The first bridged cards were the GeForce 6600 and ATI Radeon X800 XL boards, released during 2004-5.[16][17] In 2009 AGP cards from Nvidia had a ceiling of the GeForce 7 Series. In 2011 DirectX 10-capable AGP cards from AMD vendors (Club 3D, HIS, Sapphire, Jaton, Visiontek, Diamond, etc.) included the Radeon HD 2400, 3450, 3650, 3850, 4350, 4650, and 4670. The HD 5000 AGP series mentioned in the catalyst software was never available. There were many problems with the AMD Catalyst 11.2 - 11.6 AGP hotfix drivers under Windows 7 with the HD 4000 series AGP video cards;[18] use of 10.12 or 11.1 AGP hotfix drivers is the recommended[by whom?] workaround. Several of the vendors listed above make available past versions of the AGP drivers.

Connector pinout

The AGP connector contains almost all PCI signals, plus several additions. The connector has 66 contacts on each side, although 4 are removed for each keying notch. Pin 1 is closest to the I/O bracket, and the B and A sides are as in the table, looking down at the motherboard connector.

Contacts are spaced at 1 mm intervals, however they are arranged in two staggered vertical rows so that there is 2 mm space between pins in each row. Odd-numbered A-side contacts, and even-numbered B-side contacts are in the lower row (1.0 to 3.5 mm from the card edge). The others are in the upper row (3.7 to 6.0 mm from the card edge).

Accelerated Graphics Port connector pinout[6]:95[8]:231–3[9]:50
PinSide BSide AComments
1OVERCNT#+12 VUSB port overcurrent warning
2+5 VTYPEDET#Pulled low to by card indicate 1.5 V (AGP 2.0 4x) ability
3+5 VGC_DET#Pulled low to by card indicate 0.8 V (AGP 3.0 8x) ability
4USB+USB−USB pins for pass through to monitor
6INTB#INTA#Interrupt lines (open-drain)
7CLKRST#66 MHz clock, Bus reset
8REQ#GNT#Bus request from card, and grant from motherboard
9+3.3 V+3.3 V
10ST[0]ST[1]AGP status (valid while GNT# low)
11ST[2]MB_DET#Pulled low by motherboard to indicate 0.8 V (AGP 3.0 8x) ability
12RBF#PIPE#DBI_HIRead buffer full, Pipeline request, Data bus inversion[31:16]
14DBI_LOWBF#Data bus inversion [15:0], Write buffer full
15SBA[0]SBA[1]Sideband address bus
16+3.3 V+3.3 V
22ReservedReservedKey notch for 3.3 V AGP cards
24+3.3 V auxReserved
25+3.3 V+3.3 V
26AD[31]AD[30]Address/data bus (upper half)
28+3.3 V+3.3 V
40VddqVddq3.3 or 1.5 V
41IRDY#FRAME#Initiator ready, Transfer in progress
42+3.3 V auxReservedKey notch for 1.5 V AGP cards
45+3.3 V+3.3 V
46DEVSEL#TRDY#Target selected, Target ready
47VddqSTOP#Target requests halt
48PERR#PME#Parity error, Power management event (optional)
50SERR#PARSystem error, Even parity for (1x) PCI transactions only
51C/BE[1]#AD[15]Address/data bus (lower half)
66VregcgVrefgcI/O reference voltages
Ground pinZero volt reference
Power pinSupplies power to the AGP card
Output pinDriven by the AGP card, received by the motherboard
Initiator outputDriven by the master/initiator, received by the target
I/O signalMay be driven by initiator or target, depending on operation
Target outputDriven by the target, received by the initiator/master
InputDriven by the motherboard, received by the AGP card
Open drainMay be pulled low and/or sensed by card or motherboard
ReservedNot presently used, do not connect

PCI signals omitted are:

  • The −12 V supply
  • The third and fourth interrupt requests (INTC#, INTD#)
  • The JTAG pins (TRST#, TCK, TMS, TDI, TDO)
  • The SMBus pins (SMBCLK, SMBDAT)
  • The IDSEL pin; an AGP card connects AD[16] to IDSEL internally
  • The 64-bit extension (REQ64#, ACK64#) and 66 MHz (M66EN) pins
  • The LOCK# pin for locked transaction support

Signals added are:

  • Data strobes AD_STB[1:0] (and AD_STB[1:0]# in AGP 2.0)
  • The sideband address bus SBA[7:0] and SB_STB (and SB_STB# in AGP 2.0)
  • The ST[2:0] status signals
  • USB+ and USB− (and OVERCNT# in AGP 2.0)
  • The PIPE# signal (removed in AGP 3.0 for 0.8 V signaling)
  • The RBF# signal
  • The TYPEDET#, Vregcg and Vreggc pins (AGP 2.0 for 1.5V signaling)
  • The DBI_HI and DBI_LO signals (AGP 3.0 for 0.8 V signaling only)
  • The GC_DET# and MB_DET# pins (AGP 3.0 for 0.8V signaling)
  • The WBF# signal (AGP 3.0 fast write extension)


Agp Pro Slot Machine

  1. 1.01.1From the extended part of the AGP connector.
  2. The AGP Pro specifications imply a maximum of 25 W.

See also

  • Serial Digital Video Out for ADD DVI adapter cards


  1. 'AGP almost at the end, Softpedia'. 5 June 2008. Retrieved 15 September 2014.<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  2. 'What is AGP?'. Retrieved 15 September 2014.<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  3. 3.03.1'Intel 440LX AGPset'. Retrieved 15 September 2014.<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  4. Lal Shimpi, Anand (August 1, 1997). 'Chipset Guide'. AnandTech. Retrieved 2015-03-03.<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  5. 'Which version of Windows 95 supports AGP?'. Retrieved 15 September 2014.<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  6. 6.06.1Intel (July 31, 1996), Accelerated Graphics Port Interface Specification Revision 1.0(PDF), retrieved 2007-10-18<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  7. 'AGP 4×: Faster Data Transfer & Better-Quality Images'. Retrieved 15 September 2014.<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  8. 8.08.1Intel (May 4, 1998), Accelerated Graphics Port Interface Specification Revision 2.0(PDF), retrieved 2014-09-15<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  9. (September 2002), AGP V3.0 Interface Specification(PDF), retrieved 2011-10-09<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  10. AGP Pro 1.1a specification
  11. Draft AGP8× Interface Specification Rev. 0.91R
  12. 'ECS Web Site'. Retrieved 15 September 2014.<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  13. 'MSI K8N Neo3-F Motherboard Review—What's an AGR video slot?'. Retrieved 15 September 2014.<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  14. 'List of cards and chipsets that work with the MSI AGR port'(PDF). Retrieved 15 September 2014.<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  15. Allen, Mark (2006). 'AGP compatibility for sticklers'. Video card information. Archived from the original on 2012-12-21.Unknown parameter |deadurl= ignored (help)<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>
  16. Gasior, Geoff. Nvidia's GeForce 6600 GT AGP graphics card: Bridging backwards, Tech Report, November 16, 2004.
  17. Gasior, Geoff. ATI's new AGP Radeons: A bridge is born, Tech Report, May 20, 2005.
  18. 'AMD community forums'. Retrieved 15 September 2014.<templatestyles src='Module:Citation/CS1/styles.css'></templatestyles>

This article is based on material taken from the Free On-line Dictionary of Computing prior to 1 November 2008 and incorporated under the 'relicensing' terms of the GFDL, version 1.3 or later.

External links

Wikimedia Commons has media related to AGP.

Agp Pro Slot

  • AGP specifications: 1.0, 2.0, 3.0, Pro 1.0, Pro 1.1a
  • AGP compatibility (with pictures)
  • PCI Specifications Documents contains AGP specs.
Retrieved from ''

As fast and wide as the PCI bus was, there was one task that threatened to consume all its bandwidth: displaying graphics. Early in the era of the ISA bus, monitors were driven by simple Monochrome Display adapter (MDA) and Colour Graphics Array (CGA) cards. A CGA graphics display could show four colours (two bits of data) at 320 by 200 pixels screen resolution at 60Hz, which required 128,000 bits of data per screen, or just over 937 KBps. An XGA image at a 16-bit colour depth requires 1.5MB of data for every image, and at a vertical refresh rate of 75Hz, this amount of data is required 75 times each second. Thanks to modern graphics adapters, not all of this data has to be transferred across the expansion bus, but 3D imaging technology created new problems.

3D graphics have made it possible to model both fantastic and realistic worlds on-screen in enormous detail. Texture mapping and object hiding require huge amounts of data, and the graphics adapter needs to have fast access to this data to avoid the

Agp Pro Slot Software


AGP operates at the speed of the processor bus, now known as the frontside bus. At a clock rate of 66MHz this is double the PCI clock speed and means that the peak base throughput is 264 MBps.

For graphics cards specifically designed to support it, AGP allows data to be sent during both the up and down clock cycle, doubling the clock rate to 133MHz and peak transfer to 528 MBps. This is known as 2x. To improve the length of time that AGP can maintain this peak transfer, the bus supports pipelining, which is another improvement over PCI. A pipelining 2x graphics card will be able to sustain throughput at 80% of the peak. AGP also supports queuing of up to 32 commands via a process called Sideband Addressing (SBA), the commands being sent while data is being received. This allows the bus to sustain peak performance for 95% of the time, according to Intel.

AGP’s four-fold bandwidth improvement and graphics-only nature ensures that large transfers of 3D graphics data don’t slow up the action on screen; nor will graphics data transfers be interrupted by other PCI devices. Being primarily intended to boost 3D performance, AGP also provides other improvements that are specifically aimed at this function.

With its increased access speed to system memory over the PCI bus, AGP can use system memory as if it’s actually on the graphics card. This is called Direct Memory Execute (DIME). A device called a Graphics Aperture Remapping Table (GART) handles the RAM addresses so that they can be distributed in small chunks throughout system memory rather than hijacking one large section, and presents them to a DIME-enabled graphics card as if they’re part of on-board memory. The main use for DIME is to allow much larger textures to be used because the graphics card can have a much larger memory space in which to load the DRDRAM) in the second half of 1999. AGP 2.0 was supported by chipsets launched early in 1999 to provide support for Intel’s Katmai processor.

Agp Pro Slot Game

AGP Pro is a physical specification aimed at satisfying the needs of high-end graphics card manufacturers, who are currently limited by the maximum electrical power that can be drawn by an AGP card (about 25W). AGP Pro caters for cards that draw up to 100W, and will use a slightly longer AGP slot that will also take current AGP cards.